Skippers Line Polyfond
Two-component polyurethane undercoat for boats and bodywork in general. Equipped with excellent coverage and good filling power, it is used as an intermediate on wood, iron or plastic and as a preparation coat for finishing with two-component enamels (such as Acriglass, Space Top or Whitext).
0.00 Dhs
ComparePREPARATION OF THE SUPPORT AND APPLICATION CYCLE
New iron. Sandblasting to SA 2.5 grade or if it is not possible to mechanically abrasive the substrate. Apply an epoxy base coat such as EPOFOND AM-9 and let it dry for the necessary time. Then apply 1-2 coats of POLIFOND followed by the chosen finish, always observing the recommended overpainting times.
Already painted iron.If the previous finish was epoxy or polyurethane, sand and apply 1-2 coats of POLIFOND and recoat with the chosen finish. If in doubt about the origin of the pre-existing coating, sand and test a part of the surface to make sure it does not soften, come off or come off, in which case it would be necessary to completely remove the paint layer down to metal. bare and proceed as indicated for new iron supports.
New wood. Apply a coat of POLIGLASS varnish diluted 50-100% with Thinner 203 or a coat of EVIOX CROMOMINIO diluted 30-40% with Thinner 107. Allow to dry for 8-12 hours and after sanding apply 1-2 coats of POLIFOND and over paint with the chosen finish.
Already painted wood. If the previous finish was epoxy or polyurethane and in good condition, sand and apply 1-2 coats of POLIFOND and paint over with the chosen finish; otherwise completely remove the old paint and proceed as indicated for new wood.
| color | White |
|---|
| Typology | Two-component |
| Type of binder sol a | Polyester |
| Type of binder sol b | Isocyanates |
| Specific weight kg / l (± 0.05) | 1,640 (A) – 1,000 (B) |
| Dry residue (volume) | 43% |
| Storage + 23 ° C (± 2) | 24 months in sealed containers |
| 120-150 sec. (A + B) |
| Application | Roller and spray brush |
| Blend a + b by volume | 5 parts Sol A with 2 Sol. B |
| Pot life a + b (20c) | Use mixture within 6-8 hours |
| Brush-roller dilution | 15-30% Thinner 205 |
| Spray dilution | 25-35% Thinner 203 |
| Touch dry | 3-4 hours (20 ° c) |
| Overcoating time | 12-24 hours (20 ° c) |
| Application temperature | Between +10 c and +40 c |
| Relative humidity | Less than 80% |
| Recommended dry thickness | 35-40 microns per hand |
| Theoretical yield m2 / liter | 14-15 |
Brand
Skipper's Line Yacht Coatings - Made in Italy
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
-
Marine Paints, Jotun
Seaforce Shield 5L
- This is a one component high solids hydrolysing antifouling coating based on ion exchange technology.
- It provides cost efficient fouling protection. This is achieved by self polishing characteristics reducing hull
deterioration. - To be used as finish coat in immersed environments only.
- Suitable on approved primers and tie coats on aluminium and carbon steel substrates.
- It can be applied at sub zero surface temperatures.
SKU: n/a -
-
-
Marine Paints, International
International Micron 350 Antifouling Paint 2.5L
Micron antifoul has been a favourite for years among YouBoat customers, and the latest formula is no different. Micron 350 is a high strength self polishing antifouling that will offer excellent 2 seasons protection from just one application (3-4 coats)
SKU: n/a
There are no reviews yet.